Thiết bị kiểm tra độ cách nhiệt vải GESTER GT-CN08

Lượt xem:
4014
Thương hiệu:
Gester - Trung Quốc
Giá:
Liên hệ

Thiết bị bảo vệ nhiệt TPP chủ yếu được sử dụng để đo hiệu suất cách nhiệt của vải quần áo bảo hộ chống cháy tiếp xúc với nguồn nhiệt bức xạ và nguồn nhiệt đối lưu để phát hiện hiệu suất bảo vệ nhiệt của quần áo bảo hộ, giày an toàn, găng tay và bề mặt ngoài của mũ bảo hiểm.
Tiêu chuẩn: NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.

Dệt May

Feature

The test equipment shall include the sample holder assembly, the holder of the sample holder assembly, the heat source, the protective cover, the sensor assembly, the recorder, and the gasket. It shall also have a gas source, a gas flow meter, a burner, and a sensor.
Removable corundum protection board, temperature 1800 degrees, can block the flame and reduce the test error.
Two 45-degree Meker burners were placed to provide standard convection heat sources with nine quartz tubes.
Meker burner diameter 38mm, internal hole diameter 5/16 inches, can provide 800-1200 BUT heat output, the burner mouth is a metal mesh structure, the burner lower air valve can be adjusted, adjustable air and flammable gas mixture proportion.
Nine T150 quartz IR arrays provide thermal radiation flux of 13-40 kW/m2 ± 4 kW/m2.
The total heat flux can be set to 83 kW/m2 ± 2 kW/m2 by adjusting the gas supplied to the Meker burner under the heat radiation of a quartz infrared tube.
The calibration heat flow meter is water-cooled, with a working range of 0-100 kW/m2 and a maximum range of 150%.
The response time of the heat flow meter is less than 200ms, the emissivity is greater than 0.95, and the output signal is greater than 5mv in the operating range.
The copper pan calorimeter device can be used to detect convective heat and radiant heat, while detecting the temperature of the back of the specimen.
The rotameter can adjust the flow of combustion gas with an accuracy of ±2% and a range of more than 3L/min.
The pointer pressure gauge, the inlet pressure can be adjusted through the pressure reducing valve, the pressure relief valve has a range of 0-15psi.
A quarter turn plug can manually shut off the flammable gas.
The temperature acquisition system has a resolution of 0.1C° and an accuracy of ±0.75°C.
The data acquisition speed of the automated data acquisition system is sub-/0.05 second and cold junction compensation is provided for thermocouple measurement data.
Equipped with computers and printers, comes with standard test software and provides standard test curves.

Key Specifications

Model	GT-CN08
Climate Requirements	Propane and compressor air
Test Environment	25±5℃
Holding Way	Pneumatic or manual
Power Supply	220V 50Hz 15A
Dimensions	1500×540×460mm ((W×H×D)
Weight	86kg
Standards	NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.

Tập tin PDF:

Sản phẩm cùng loại

Chi tiêt Xem nhanh

Lab Calender Model LC-250

Hãng sx: RAPID (Labortex)

Lab Calender Model LC-250 is suitable for calendaring test by controlling pressure, heat and friction applied on fabric surface. The machine consists of two rollers placed vertically, the upper roller is made of Nylon, the lower steel roller as a heater, driven by a motor to rotate.

Liên hệ

Chi tiêt Xem nhanh

Laboratory soaping machine model SP-12

Hãng sx: RAPID (Labortex)

Laboratory soaping machine model SP-12 is a 12-position unit used for after-treatment processes of dyed samples (yarn or fabric) as well as printed textiles. Samples are placed in different stainless steel pots, operators may add chemicals manually , then agitated them in the heating bath. Suitable for many kinds of after-treatment processes, such as soaping, scoring, bleaching, cotton burn-out in sulfuric acid, etc.

Liên hệ

Chi tiêt Xem nhanh

LEATHER DYEING APPARATUS

Hãng sx: RAPID (Labortex)

A versatile apparatus for dyeing tanning, leather and other processes in the production of leather * Max. dyeing temperature: 98 ℃ * Electric heating system * Revolving speed infinitely variable * Drum diameter: 250mm or 150mm * No. of drum: 8 (other available on request)

Liên hệ

Chi tiêt Xem nhanh

Laboratory centrifuge TS-1

Hãng sx: RAPID (Labortex)

Laboratory centrifuge TS-1 is used to remove excess water from samples after dyeing or washing before hot-air drying. Simple operation, NO technical skills are required

Liên hệ

Chi tiêt Xem nhanh

COLOR WASHING FASTNESS TESTER (RAPID WASH)

Hãng sx: RAPID (Labortex)

This testing machine RAPID WASH is specially designed to conduct color fastness testing in compliance with all major international standards.

Liên hệ

Chi tiêt Xem nhanh

PRINTING MASTER PM-500

Hãng sx: RAPID (Labortex)

This exceptional machine perfectly eliminates the inconsistency caused by manual operation, not only helping laboratories with automation, but also ensuring reproducibility between each test. With an electromagnetic bar for flatbed screen, printing speed, operating range and pressure of the scroller bar are adjustable through electromagnets. Operators can pre-set all relevant parameters in the touch screen controller. The printing table is equipped with special holders to fix the screen in the correct position.

Liên hệ

Chi tiêt Xem nhanh

AUTOMATIC WASHING MACHINE AW-12

Hãng sx: RAPID (Labortex)

AW-12 is indispensable Lab equipment used for carrying out post-processing such as washing, scoring and soaping for dyed yarn, fabric or any textile samples. Users just need to place textile samples into stainless steel washing pots, then water adding, chemical dosing, washing as well as draining will be automatically processed by a programmable controller. Samples with solution can be gently agitated by air turbulence which is introduced by blowers, therefore, manual stirring is no longer required.

Liên hệ

Chi tiêt Xem nhanh

Laboratory ROLL MILL

Hãng sx: RAPID (Labortex)

Laboratory ROLL MILL is a compact model with lowest noise level, highest safety, its specially-designed electric heaters evenly and accurately radiate heat to achieve the required surface temperature according to the command given by two modernized temperature controllers.

Liên hệ

Chi tiêt Xem nhanh

AUTO COATING DEVICE

Hãng sx: RAPID (Labortex)

AUTO COATING, an indispensable device for laboratory coating process. For conventional coating process, the inconsistent speed and pressure always causes serious problem regarding uneven coating quality. Our AUTO COATING device is designed to fulfill in every coating necessity with the best reproducibility.

Liên hệ

Chi tiêt Xem nhanh

LABORATORY MINI OVEN

Hãng sx: RAPID (Labortex)

LABORATORY MINI OVEN is designed to be paired up with our AUTO COATING device. The integrated pin-frame is compatible with both machines; therefore, samples can be directly moved to this hot-air oven for drying treatment after coating without any re-pinning process.

Liên hệ